The Kirby Morgan 67 Diving Helmet continues in our long tradition of innovation, providing the highest quality and superior performance that divers have come to expect in a Kirby Morgan product. At first glance, you’ll notice that the helmet features our revolutionary new SBR-1™ Stainless Balanced Regulator and have a different port design, but the differences go much deeper than just the visual. Don’t confuse the SBR-1™ with a sport diving regulator - it’s designed from the ground up strictly for commercial diving. With a rugged extra long adjustment knob and shaft, the SBR-1™ meets the wide range of breathing gas pressure provided by typical low-pressure surface-supplied compressors. It’s machined from a stainless steel casting for the ultimate in performance and reliability. This commercially rated regulator delvers all the breathing gas you need for the most demanding work underwater.

The Kirby Morgan 67 also includes our Quad-Valve™ Exhaust System. It’s recommended for diving biologically contaminated water, when you’re properly trained and equipped, using recommended procedures. This new exhaust has exceptionally low exhalation resistance that you must experience to appreciate

Our new Ultra View™ Port Design isn’t just wider, it’s also thicker, much thicker, which is essential to your safety when your port is this wide. It’s also through bolted, which is unheard of in diving helmet, but makes you think about it. If you ever strip a retainer bolt, which is unlikely given their size, just replace it and its special securing nut without special tools or procedures.

The Kirby Morgan 67 sets the standard for a new generation of diving helmets. If you want the ultimate diving helmet, there’s really no other choice. Check out the Kirby Morgan 67 today…

CAUTION: Before attempting any diving in any type of contaminated environment, a complete top side course in hazardous materials emergencies should be completed. For more complete information see the book "Diving in High-Risk Environments" by Steven M. Barsky

A__Side & Top Weights bring unsurpassed balance to the helmet while providing for accessory mounting areas.

B__ Fiberglass and Carbon Fiber Reinforced Shell
Kirby Morgan has over 50 years experience in composite laminations. The helmet shell is hand laid up glass fiber reinforced thermal setting polyester (fiberglass) with carbon fiber reinforcement at key points for added durability. It is light and highly impact resistant, and provides a heat/cold barrier as well as being an excellent electrical nonconductor.

C__Defogging Steady Flow Valve
provides an additional flow of gas into the helmet for ventilation and defogging.

D__Emergency (EGS) Valve
supplies backup breathing gas to the diver.

E__Gas Supply Non-Return Valve
is Commercial Rated™. It prevents loss of
gas pressure in the event of umbilical damage.

F__Rapid Change Modular Communications System
Because the module is easily removed from the helmet, repair or replacement of communications parts is quick and trouble free. It is available with either a male waterproof connector or a bare wire post connection.

G__Head CushionPositive-Lock™ Latch System
This latching system, developed by Kirby Morgan in 1992, consists of two sealed Positive-Lock™ pull pins which are pulled forward to release the neck collar and neck dam locking system. Even when the latches are released, the O-ring sealed neck dam maintains a positive seal and will not allow the seal to be broken until the collar actually clears the diver's shoulders, thus helping to prevent any flooding of the helmet.

H_ Head Cushion
The Head Cushion gives the helmet a secure, well balanced feel as well as excellent thermal protection during long work periods.

I_ Air Train diffuses the incoming breathing air/gas onto the face plate to defog the lens.

J Silicone Oral Nasal Mask is made of a superior silicone material which is hypo-allergenic and has a longer work life than latex.

K) New UltraViewTMP ort Through bolted, ultra wide, ultrarugged design, unlike any other diving helmet. Thickness is proportional to surface area for better safety. This is the largest port available on any diving helmet.

L) Nose Block Device allows the diver to block the nose to equalize ears.

M) SBR-lTM Stainless Balanced Regulator. This balanced, stainless steel, Commercial RatedT" demand regulator provides easy breathing and excellent performance with low-pressure compressors.

N) Quad-ValveTMExhausSt ystem. Makes the helmet very dry with no loss of breathing performance.

0 ) Externally Adjustable Chin Strap. The externally adjustable chin support, along with the adjustable neck pad on the locking collar gives the diver a comfortable, secure fit.

P) Adjustable Neck Pad. The helmet attached yoke system has an adjustable neck pad which is made from a scuff resistant elastomer. In conjunction with the spring activated front neck dam ring lock, it provides protection for the bottom of the Helmet.